20th Century Fox: Fox No. 24 Typewriter Reassembled

I have been cleaning and tinkering with my Fox No. 24 typewriter for the past few weeks.

Sugru for Key Letters

It look like someone – in a fit of boredom – took a ballpoint and scratched out a couple of the letters on the Fox’s keys. I got some white Sugru at Target for the key tops where the lettering has worn off.  Sugru is a self-setting rubber product that is removable. I pressed it into the key letter depressions and scrapped away the excess.  It sets in about 24 hours.  If I change my mind about the letters later on down the road, I can peel it off.



Not too shabby; now the letters are readable. The letters are a bit white; I may tone them down a bit with a yellowish glaze.


A testament to her true grit, the Fox was able to type with two broken shifting arms. The broken arms were causing typebar alignment problems though, so they needed to be re-secured. I initially tried to re-attach the broken back corner, front frame section and broken shifting arms with J-B Weld SteelStik. Unfortunately the SteelStik was not “tacky” enough and wasn’t adhering to the pieces of broken cast iron (despite sanding and cleaning), so I used J-B KwikWeld metal epoxy adhesive which is a bit stickier.


Foxini supervises the work

I had to remove the shifting arms to glue them because there was considerable sag in the adhesive – the pieces needed support while the adhesive dried.


Done broke


Broken ends sanded with rough sand paper and cleaned with denatured alcohol before the epoxy applied – it’s a little gloppy.

The rear left corner was a crumbled mess – it’s a bit better now after some J-B Weld, but it could use a good sanding to smooth out irregularities.


The Rust Blackened

There are many areas of bare metal on the painted surfaces.  I was torn.  Should I use Testor’s model paint which is a great match and very permanent, or should I go with India ink (encre de Chine) which is a great match and less permanent?  I went with the India ink and a light coat of Renaissance Wax.  Some future owner may want to undo what I have done.  I want to be sensitive to the history of the machine and preserve as much vintage authenticity as possible.


Finally, I flushed out the metal internal guts with mineral spirits and compressed air. I was worried about excess PB B’laster attracting dirt and gumming up things down the line.

I mixed myself a stiff drink, fired up a cigar, leaned back, and drank in the physical beauty of this 100-year-old vixen. Make no mistake: this is a 100-year-old typewriter that has suffered catastrophic neglect and damage. However.  She is still very fine indeed.


American Fox-es! (spoken with Festrunk brothers’ emphasis)


Model number 24 – somewhat hidden behind the keyboard:


I wish I had better luck removing the cracking layer of yellow varnish/lacquer/shellac around the decals.  I tried to Soft Scrub it off, but I wasn’t successful.  I will leave it to some future restorer with better products and methods.


The back decal (“The Fox”) has worn off or been painted over:


Lots of luscious curves in back though:


Baby got back

The decal on the left side of the machine is in good condition:



What Does the Fox Say?

The darn thing types like the proverbial champ:


It’s got fun special characters: manicules, pilcrow, section sign and degree characters.


It has a double row of staggered type bars. These are called pin-mounted slugs, right?


The carriage comes off with four loosened screws.  You loosen the carriage scale pointer screws, slide the carriage scale pointer over and off; loosen the carriage screws, secure the draw string to the hitching post, and the carriage lifts off.


dismantled prior to de-rusting

What a wonderful machine. After spending some time in genuine appreciation, I got down to typing.

Fox on the Run

Here’s a looping six second video of me typing away happily on my quick black Fox.


How about another six second loop?


To Do List

  • Continue polishing rusted and corroded parts – there is still so much to clean up. I hope I get that high-capacity ultrasonic tank full of solvent for Christmas🙂
  • Try heat shrink tubing for a couple of the feed rollers which are a bit brittle and disintegrating.
  • I need to figure out the line lock set up. My Fox keeps typing at the end of the line, and I think there may be a rust problem that prevents the line lock from engaging.  I am looking at the patent documents for clues.

Crumbly feed rollers and surprise! more rust

This is what I want for Christmas.  Friends and family, please take note:




6 thoughts on “20th Century Fox: Fox No. 24 Typewriter Reassembled

  1. Tyler Anderson says:

    I applaud your wonderfully successful efforts. Now I’m just curious what downtrodden machine will get the patented M-O-T Restoration Treatment (c)


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s