Smokin’ Ball Bearing Action: L.C. Smith No. 8

Since I got back from a recent family vacation,  I have been alternating working on the 1922 L.C. Smith No. 8 and the Century 10.  I have been switching back and forth. When I run out of ideas on one, I move to the other.

Ball Bearings at All Frictional Points!

When I first brought the L.C. Smith home, there were several immobile keys – the basket was dusty, rusty and gummed-up. And there was a circa 1920 cigar cutter jammed between the universal bar and the line lock bail.

After cleaning with denatured alcohol, the typewriter began to type and type beautifully. I happily typed out a long letter and it loosened more and more with each printed line.  It has a light, springy touch which I assume is due to the ball bearings in the typebars. It is a joy to type on. Robert Messenger has a great post on his L.C. Smith 8 typewriter that includes images of early advertisements which extol the virtues of the L.C. Smith’s “ball-bearings at all frictional points”. If I were a decent typist, I could go smokin’ fast on this one.

My L.C. Smith’s most major problem is rust, especially underneath the machine.  I would love to dunk her in an Evapo-Rust bath, but unfortunately Evapo-Rust is not friendly to paint – it softens up the paint quite a bit.  It also leaves a messy, sticky sort of residue.  I use it only for parts that I can remove, soak, and polish up afterwards.

So here is all the fun I had with the L.C. Smith:

Shift lock not holding

Could it be that the Enormous Grotesque Foot is interfering with the motion of the shift lock? Why, yes. I removed the foot and the shift lock was able to move.


The machine needed three feet, and I cut some really classy looking feet out of cork and colored them with black Sharpie.

Original foot on left. Cork replacement foot being carved into shape.

Original foot on left. On right: cork replacement foot being carved into shape. Covered in Sharpie.

Thanks for the cork replacement foot idea, JustAnotherGuy.

Left carriage release not working

I compared right and left carriage release mechanisms and determined that a lever wasn’t in the right spot.





I loosened a screw, moved the lever to the correct spot, re-tightened the screw, and all was well.

Dirty platen

Yes, it was FILTHY.  I typed a letter to a fellow typospherian and there was debris all over the page.


It is very easy to remove the platen from an LC Smith No. 8.  It it held in place with a screw at each end in a knobbed plate and then pops right out. So easy – I wish they were all like this.



The platen is nice and soft and cleaned up beautifully with a little Soft Scrub.  From the Craigslist pictures, I thought there were rips in the platen, but it was just crusts of rust.

Missing tab connectors

Functional tabs are little low on my list of priorities, but the missing tab linkages and sunken keys bugged me.

Missing tab connectors

Missing tab linkage


Resulting in sunken tab keys

I cut some thin pieces of metal to size to temporarily replace the missing connectors. I need more rigid metal if I want to use the tabs, but these work for keeping the sunken keys up.

new tab connectors made from thin metal

New tab connectors made from thin metal


Tab keys sunken no more

Outstanding Issues:

Malfunctioning line lock

This is still an issue I haven’t been able to resolve.  I get to the end of a line and the typewriter allows me to continue typing, piling letters on top of letters at the end of the line.  The line lock should engage at the end of the line, but doesn’t.  The line lock bail is rusted into position and does not move at all.  I am getting some Liquid Wrench today to see if I can free it.

Missing tab stops

The tab stops are nowhere to be seen (and I didn’t see them under the universal bar with the cigar cutter).  I went to internet and asked about it.  I am not the first person to run into this problem.

I love Knife141’s posts at Instructables: this guy Gets It Done. I have run across his very informative posts before:

Knife141 has a post called, “Making tab stops for an LC Smith Typewriter”.  I have bookmarked this page so that if ever I get ambitious, I will make those tab stops.

The vertical alignment of the capital letters is a bit high

This typewriter is basket shift. The capital letters are printing a little high:


Thanks to Knife141, I believe that I need to make an adjustment to the nuts directly under the segment to bring it to the right height with shifting. I just don’t have the right size crescent open end wrenches, but Good Neighbor Brian has offered the use of his set. First off though, I need to get some Liquid Wrench because the nuts are very rusty.


Cleaning, touch up and waxing

I cleaned the exterior of the typewriter with soap/water and a little Soft Scrub.  I was very careful around the decals – cleaning all around them.

I touched up the bare metal spots with a very thin layer of Testor’s black paint pen that I rubbed on. Sharpie was not a good match, but the paint pen was very close. On future projects, I’d like to experiment with India Ink (Encre de Chine) which was suggested by RobertG as it is less permanent and is an almost perfect match.

I bought some Renaissance wax polish and shined up the typewriter.  I avoided the decals as I was worried that I might rub them off. I don’t know if this is a legitimate worry with the Renaissance wax, but I didn’t want to take the chance. I love those insane horsies so much.

1922 L.C. Smith No. 8

Serial number: 460128-8

I’ve attached the cigar cutter with a ribbon to the typewriter for easy access. I believe that the “best practices” use of this machine involves cigar smoking, so I lit up a stogie and enjoyed an afternoon of typing en plein air.






15 thoughts on “Smokin’ Ball Bearing Action: L.C. Smith No. 8

  1. Michael Höhne says:

    Great post! Informative and useful!

    Crescent wrenches are adjustable, y’know, and because of that they’re pretty big; maybe you mean open-end wrenches. At your automotive store, get a set of Ignition wrenches. They are very small and very useful on typewriters.


    • Ha! I am still a little shaky on my tool terminology. Thank you for the automotive store tip. I couldn’t find any teeny wrenches at the hardware store, but the automotive store may be just the ticket.


  2. Wonderful, all of this!

    Renaissance Wax has never harmed decals in my experience. Of course, apply it gently.

    I recently got some deruster on eBay which used the name “Evaporust” in its auction title but is actually an imitation. Probably the chemical principle is the same. It worked just fine, and was clear and wholly non-sticky.


  3. JustAnotherGuy says:

    Great job, that LC Smith looks fantastic. I’ve found some interesting things inside of typewriters (my favorite was a receipt from a repair shop!) but I think the cigar cutter beats them all! Your cork feet sure look better than mine does.


  4. These are relatively easy to work on and so rewarding when they do work. I think these old LC Smiths might be my favorite non-portable machines to type on.


  5. Great and impressive to see how such a machine comes back to life and improves its looks too. Think it really is fun to be able to tackle these issues of a machine🙂
    And of course, like a user instruction for HMV gramophones put it; “disuse is bad for the machine” – mechanical machines do benefit from being used.


Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s